Back to Top

Hi, Guest!

  LOKASI :  Bekasi Utara (Harapan Indah)

Bergabung Selama :

BAGIKAN :   

Bagikan :
  • ASTM C881 / C881M - 10 Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete

ASTM C881 / C881M - 10 Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete

Update Terakhir
:
01 / 12 / 2019
Min. Pembelian
:
1 Unit
Dilihat Sebanyak
:
42 kali

Harga

CALL
Bagikan
:
NOVKA TEKNIK bergerak dalam bidang perdagangan alat-alat untuk proyek kontruksi seperti mesin bobok/ jack hammer/ breaker, mesin bor/ drilling beton, paku tembak/ ramset, chemical angkur, mechanical angkur dan plastick angkur. bila Bapak/ibu memerlukan bantuan, jangan sungkan untuk menghubungi kami kapan saja. Akhmadi Heru telpon :  0858 6846 2560

Perhatian !

Perusahaan ini terdaftar sebagai Free Member. Hindari melakukan pembayaran sebelum bertemu penjual atau melihat barang secara langsung. COD (Cash On Delivery) atau bertemu langsung dengan penjual merupakan metode transaksi aman yang kami sarankan.

Detail ASTM C881 / C881M - 10 Standard Specification For Epoxy-Resin-Base Bonding Systems For Concrete

ASTM C881 / C881M - 10 Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete This specification covers two-component, epoxy-resin bonding systems for application to Portland-cement concrete, which are able to cure under humid conditions and bond to damp surfaces. The epoxy-resin bonding systems are classified according to type, grade, class, and color. The bonding systems can be classified as Type I, Type II, Type III, Type IV, Type V, Type VI, and Type VII according to their physical requirements. According to their flow characteristics and viscosity, the bonding systems can be classified as Grade 1, Grade 2, and Grade 3. Also, in accordance with the range of temperatures for which they are suitable, these materials can be designated as Class A, Class B, Class C, Class D, Class E, and Class F. Classes A, B, and C are defined for Types I through V, and Classes D, E, and F are defined for Types VI and VII. Epoxy resin systems are normally unpigmented, but they can be colored or darkened. These bonding systems shall be furnished in two components for combining immediately prior to use in accordance with written instructions formulated Component A shall contain an epoxy resin with or without a reactive diluent. Component B shall contain one or more curing agents, which on mixing with Component A shall cause the mixture to harden. A suitable inert filler may be uniformly incorporated in one or both components. The filler shall be either nonsettling or readily dispersible in any component in which it is incorporated. All systems shall cure under humid conditions, and bond to damp surfaces. Different test methods shall be performed to determine the following properties: consistency, gel time, filler content, epoxy equivalent, viscosity, absorption, bond strength, thermal compatibility, heat deflection temperature, linear coefficient of shrinkage, compressive yield strength and modulus, tensile strength and elongation at break, and contact strength. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. 1. Scope 1.1 This specification covers two-component, epoxy-resin bonding systems for application to portland-cement concrete, which are able to cure under humid conditions and bond to damp surfaces. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Some values have only SI units because the inch-pound equivalents are not used in practice. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see Section 9. 2. Referenced Documents ( purchase separately) ASTM Standards C882 Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear C884/ C884M Test Method for Thermal Compatibility Between Concrete and an Epoxy-Resin Overlay D570 Test Method for Water Absorption of Plastics D638 Test Method for Tensile Properties of Plastics D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position D695 Test Method for Compressive Properties of Rigid Plastics D1084 Test Methods for Viscosity of Adhesives D2566 Test Method for Linear Shrinkage of Cured Thermosetting Casting Resins During Cure
Tampilkan Lebih Banyak